If you’re like most people, you probably don’t think about changing the blade on your Craftsman table saw very often. But if you use your saw regularly, or if it’s been a while since you’ve changed the blade, it’s a good idea to know how to do it. Here’s a step-by-step guide to changing the blade on a Craftsman table saw.
- Unplug your saw from the power source
- Raise the blade to its highest position
- Loosen the blade arbor nut with a wrench
- Remove the old blade from the arbor and discard it
- Install the new blade onto the arbor
- Tighten the blade arbor nut with a wrench
- Lower the blade to its original position
- Plug your saw back into the power source
How to Replace a Craftsman Table Saw Blade
How do you change the blade on a old Craftsman table saw?
If you’re like me, you have an old Craftsman table saw that you bought used. It’s a great saw, but the blade is getting dull and needs to be replaced. Here’s how to do it:
1. Unplug the saw and make sure it’s not plugged into an outlet.
2. Remove the blade guard.
3. Use a wrench to loosen the arbor nut.
4. Remove the old blade.
5. Install the new blade.
6. Re-install the arbor nut and blade guard.
7. Plug the saw back in and you’re ready to go.
How do you take the blade off a Craftsman circular saw?
Assuming you’re referring to a standard handheld circular saw, the process is fairly straightforward. There are typically two screws on the underside of the saw that hold the blade in place. Simply remove these screws and the blade will come off.
If the saw is a worm drive saw, the process is a bit different. There will be a large nut on the side of the saw that needs to be loosened before the blade can be removed.
In either case, it’s always a good idea to unplug the saw before attempting to remove the blade.
Safety first!
How do I remove a table saw blade?
If you need to remove a table saw blade for any reason, the process is actually pretty simple. First, unplug the saw from the power source. Next, raise the blade up to its highest position and secure it in place with the blade guard.
Then, remove the throat plate. At this point, you should be able to see the arbor nut. Use a wrench to loosen and remove the arbor nut.
Once the nut is off, the blade can be removed. Be careful when handling the blade, as it will be sharp. Finally, reverse the process to install the new blade.
How do you put a blade on a Craftsman saw?
There are a few different types of Craftsman saws, so the process for putting a blade on them will vary slightly depending on the model. However, the general process is as follows:
1. Start by disconnecting the saw from any power source.
2. Next, remove the blade guard from the saw.
3. Then, loosen the tension knob on the saw. This will allow you to remove the old blade from the saw.
4. To install the new blade, simply reverse the above process. Start by aligning the new blade with the blade mount, then tighten the tension knob to secure it in place.
5. Finally, replace the blade guard and reconnect the saw to a power source.
Credit: www.searspartsdirect.com
How to change blade on craftsman 10 inch table saw
It is important to know how to change the blade on your Craftsman 10 inch table saw, because over time the blade will become dull and will need to be replaced. Here are the steps to follow to change the blade on your Craftsman 10 inch table saw:
1. Unplug the saw from the power source.
2. Raise the blade to its highest position.
3. Use the blade wrench to loosen the blade nut.
4. Remove the old blade.
5. Install the new blade.
6. Tighten the blade nut.
7. Lower the blade.
8. Plug the saw back in to the power source.
That’s all there is to it! By following these simple steps you will have the Craftsman 10 inch table saw blade changed in no time.
Craftsman table saw blade removal tool
If you’re a woodworker, you know that one of the most important tools in your workshop is the table saw. And one of the most important parts of the table saw is the blade. So when it comes time to remove the blade, you need to use the right tool for the job.
The Craftsman table saw blade removal tool is the perfect tool for the job. It’s designed to fit all Craftsman table saws, and it has a comfortable grip that makes it easy to use. The blade removal tool also has a built-in blade guard that protects your hands while you’re working.
To use the Craftsman table saw blade removal tool, first make sure that the table saw is unplugged. Then, open the blade guard and remove the blade. Next, insert the blade removal tool into the blade arbor and unscrew the blade nut.
Finally, pull the blade out of the arbor and dispose of it properly.
How to change a table saw blade
If you’re like most people, you probably don’t think much about the blade on your table saw. But, if you’re not careful, it’s easy to damage the blade and end up having to replace it. Here’s how to change a table saw blade:
1. Unplug the saw and make sure the blade is stopped.
2. Raise the blade and remove the table insert.
3. Remove the blade guard.
4. Use a wrench to loosen the blade nut and remove the blade.
5. Install the new blade and tighten the nut.
6. Reinstall the table insert and blade guard.
7. Lower the blade and plug the saw back in.
8. Test the saw to make sure it’s working properly.
If you follow these steps, you’ll be able to change the blade on your table saw quickly and easily.
Conclusion
If your table saw is anything like mine, then the blade is probably one of the most important parts. Over time, the blade will get dull and will need to be replaced. Here is a quick guide on how to change a craftsman table saw blade.
First, you will need to remove the old blade. To do this, simply unscrew the blade retaining nut with a wrench. Once the nut is loose, the blade can be removed by sliding it off of the arbor.
Next, take the new blade and slide it onto the arbor. Make sure that the blade is facing the correct direction before tightening the retaining nut. Once the nut is tight, you can put the table saw back together and start using it again.