If you’re looking for a breaker for a 5HP air compressor, you’ll need one that’s at least 40 amps. However, it’s always best to consult an air compressor specialist to find out the specific size and model that will work best for your needs. There are a lot of different factors to consider when it comes to finding the right air compressor, so it’s important to do your research and make sure you’re getting the best possible model for your needs.
When it comes to sizing a breaker for a 5hp air compressor, there are a few things to keep in mind. First, the rule of thumb is that the breaker should be sized at least 1.5 times the full load current of the compressor. So, for a 5hp air compressor, the full load current would be about 20 amps.
Therefore, a 30-amp breaker would be the minimum size you would need.
Of course, there are other factors to consider as well, such as the length of the circuit and the type of wire being used. But as long as you keep the 1.5 rule of thumb in mind, you should be able to size a breaker for a 5hp air compressor properly.
How to Properly Wire a 220 volt 5HP Air Compressor per NEC part 2
How many amps does a 5hp air compressor use?
A 5hp air compressor typically uses about 20 amps.
What size breaker does an air compressor need?
When it comes to finding the right size breaker for an air compressor, there are a few things to keep in mind. First, you’ll need to know the voltage of the compressor. Most air compressors operate on either 120 or 240 volts.
Once you know the voltage, you can determine the amperage rating of the breaker.
For a 120-volt air compressor, a 20-amp breaker is typically the right choice. For a 240-volt compressor, you’ll usually need a 30-amp breaker.
However, it’s always best to check the owner’s manual for the specific amperage rating required for your air compressor.
Once you know the necessary amperage, you can choose the right size breaker. Be sure to select a breaker that is compatible with the voltage of your air compressor.
Choosing the wrong size breaker could damage your compressor or cause other problems.
What size wire do I need for a 5 hp motor?
If you are looking to wire a 5 horsepower motor, you will need to use at least an 8 gauge wire. This wire size will be able to handle the amps that will be drawn from the motor. If you are using a higher voltage than what the motor is rated for, you will need to use a larger wire size.
Is a 5hp compressor good?
Assuming you are talking about an air compressor:
The answer to this question depends on a few factors. How big of an area do you need to be able to cover?
What is the maximum PSI that you need? How often do you need to use it?
A 5hp air compressor can be a good option for some people.
It can provide enough power to operate most small air tools, and it is not too loud. However, it may not be powerful enough to run large air tools or to be used for extended periods of time.
Credit: eatoncompressor.com
Air compressor wire size calculator
If you’re in the market for an air compressor, one of the first things you’ll need to do is calculate the proper wire size for your unit. This is a critical step, as using the wrong size wire can lead to fires, shorts, and other serious problems.
Luckily, there’s a simple formula you can use to calculate the right size wire for your air compressor.
Just take the following steps:
1. Determine the maximum amperage rating of your air compressor. This information can be found on the compressor’s nameplate.
2. Multiply the maximum amperage by 1.25. This safety factor will ensure that your wire can handle any surges or spikes in amperage that may occur.
3. Use the resulting number to find the correct gauge wire from the chart below.
Now that you know how to calculate the proper wire size for your air compressor, it’s time to get out there and get started on your project!
5hp 230v single phase motor breaker size
A single phase motor draws less current than a three phase motor of the same horsepower rating, so a smaller circuit breaker can be used. For example, a 5 horsepower (hp) three phase motor may require a 20 amp circuit breaker, while a 5 hp single phase motor will only require a 15 amp breaker.
What size breaker for 80 gallon air compressor
An 80-gallon air compressor is a large appliance that requires a 220-volt circuit to operate. The size of the breaker required to power this appliance depends on the amperage rating of the air compressor. Most air compressors have a rating of 15 or 20 amps, so a 20-amp breaker is generally the appropriate size for an 80-gallon air compressor.
However, it is always best to consult the owner’s manual for the specific amperage rating of your air compressor before selecting a breaker.
Conclusion
A 5hp air compressor requires a breaker with a capacity of at least 10 amps.